by Alicia Guarasci Alicia Guarasci

6 Inch Belt Washer – Wash, Rinse & Blow Off (2 Units Available)

Used 6 Inch Belt Washer for sale. This unit includes the following features:

  • Both belt washers never in production; brand new; test run at factory
  • JENFAB 6″ Belt Washer (wash / rinse / self-generated air blow off Top and Bottom surface).  
  • Overall  152” long x 86” wide x 88” high 
  • 480v 3 phase
  • Stainless steel construction of wash tank &  rinse tank – insulated
  • Electric heat to 140 degrees for each tank, 
  • Regen ambient blow off air top and bottom surface only
  • Variable speed drive for belt (1 to 4 FPM)
  • Stainless steel  belt, 6” wide 1/2″ x 1/2” 
  • Disk oil skimmer for wash tank 
  • Dosatron dispenser     
  • Digital temperature controller for 140F Tank Heat systems
  • Chip collection tray-  304 stainless steel 1/16 perforations        
  • Confinement screen inside around belt to prevent part blow off                              
  • SS Drain Header and Valves
  • Tank overflow and bottom tank drains plumbed to a common drain header
  • Side spray headers with stainless steel nozzles, one tied to bottom header, one tied to top header
  • Exhaust fan with damper mounted to the top of the machine enclosure
  • Removable belt enclosure side access panels, allows better access to bottom spray nozzles
  • Wash tank  190 gallons
  • Rinse tank  145 gallons
  • Tunnel opening 7” wide x 6” tall
  • Weight capacity – 500lbs evenly distributed
  • Owner ordered 2 belt washers for new cell assembly.
  • Determined upon arrival washers would not fit into cell.

                    

6 Inch Belt Washer
6 Inch Belt Washer
6 Inch Belt Washer
6 Inch Belt Washer
6 Inch Belt Washer
6 Inch Belt Washer

*As is, where is, loaded on truck, FOB Arizona.*

For purchasing information, email sales@blast-wash-systems.com or Contact Us.

SUPERSTRUCTURE AND HOUSING:
Base:                       11 gauge formed 304 SS 
Walls:                      11 and 14 gauge 304 stainless steel   
Top Removable covers, 304 stainless steel  
Baffles Between all spray stations, 304 stainless steel  

 

       

TANKS:
Tank Material 11-gauge 304 stainless steel, double welded sloped bottoms to drains
Tank Covers large lift off, 304 stainless steel , with handles 
Drain Size:                 1 ¼”
Overflow Size:              1 ¼”
Water Inlet:                ¾” Copper sweat with manual fill valves for each tank, (SS optional)
Fluid Level Control Included for each Tank, Ball Float tied to main water header
Insulation  2″ fiberglass block between inner wall and outer skin, exterior surface 

is14 gauge mill grade 304 SS outer skin

Chip Baskets 6″ diameter  stainless steel mesh mounted with full drain pan  
Heat: 140° with thermostat-controlled stainless steel heaters 

               

 

SPRAY SECTION

WASH SECTION SPRAY SPECIFICATIONS:

Length: DOT 48″  with drain area and entrance vestibule
Pump Make:                  Gusher (or equal) all-iron vertical pump (No Seal)
Pump Capacity 50 GPM, 30 PSI, 3 HP
Tank Capacity:              190 Gallons
Solution  Temp 140 degrees with electric heating elements, 27 KW over the top Heating Element
Piping:                     Schedule 40 black iron positioned to properly direct spray, top and bottom 
Spray Nozzles: Non metallic clip on with SS V Jet Nozzles, Nozzles Easily adjusted to angle Spay Pattern
Level Control Ball Float tied to main water header with shut off valve

                   

           

SPRAY SECTION

EACH ADDITIONAL RINSE OR INHIBIT ZONE SPRAY SPECIFICATIONS:

Length: DOT 36″ with drain area and entrance vestibule
Pump Make:                  Gusher (or equal) all iron vertical, Seal Less
Pump Capacity 50 GPM, 30 PSI, 3 HP
Tank Capacity:              145 Gallons
Solution Temperature 140 degrees with 27 KW electric heating elements, 
Piping:                     Schedule 40 black iron positioned to properly direct spray, top and bottom and 
Spray Nozzles: Nonmetallic clip on with SS V Jet Nozzles, Nozzles Easily adjusted to angle Spay Pattern
Level Control Ball Float tied to main water header with shut off valve
Return Belt Shroud A SS Shroud Encapsulates the Return Belt in Rinse section to prevent Drag over from Rinse to Wash Tank

 

AIR BLOW OFF 

SPECIFICATIONS:

Length: DOT 34″ Top over belt and Bottom between Belt Air Delivery
Motor 15 HP, 1750 RPM, TEFCBB with centrifugal Regen blower, 550 CFM 
Heat (Optional) 10 KW standard 
Air Knives Stainless steel construction with engineered slots for Air Delivery, Air Knives are Easily Adjustable for angle and height over and below the belt. Two Twelve (12) Inch Air knives positioned on top and On bottom (Side air blow off and heat for Blow Off is optional)
Note: Standard blow off has air flow from top and Bottom only.  Optional air flow from sides is available with appropriate increase of blower size and increase in heat (optional).